Extension Machine (for round steel and threaded steel)

Mesin Pemanjang (untuk baja bulat dan baja ulir)

Mulai $1,000

Mesin ekstensi untuk penipisan baja bulat — universal untuk baja bulat dan baja berulir.

Kategori:

From $1,000

⚙
Dapat disesuaikanSemua parameter dapat disesuaikan dengan kebutuhan produksi Anda. Harga akhir dikutip sesuai spesifikasi yang telah Anda konfirmasi.

Ringkasan

Mesin tarik ini mengurangi diameter batang baja bulat sebelum pemrosesan lebih lanjut, dan juga cocok untuk baja bulat dan baja berulir (terdeformasi). Tersedia dalam tiga ukuran yang mencakup Φ6–10 mm, Φ6–12 mm, dan Φ6–16 mm.

Fitur Utama

  • Universal — dapat digunakan pada baja bulat dan baja berulir
  • Tiga model: 550, 650, 750
  • Mencakup Φ6–10 mm hingga Φ6–16 mm
  • Penggerak 18.5 kW hingga 37 kW
  • Terintegrasi dengan lini pelurus dan pemotong kawat

Spesifikasi Teknis

Model 550 650 750
Daya motor 18.5 kW 22 kW 37 kW
Diameter gulungan Φ550 Φ600 Φ800
Spesifikasi Φ6–Φ10 Φ6–Φ12 Φ6–Φ16

Kirimkan kepada kami rentang diameter kawat, material, dan keluaran yang dibutuhkan — insinyur kami akan mengonfirmasi spesifikasi persisnya dan memberikan penawaran harga dalam 24 jam.

Ulasan

Belum ada ulasan.

Jadilah yang pertama memberikan ulasan “Mesin Pemanjang (untuk baja bulat dan baja ulir)”

Your email address will not be published. Required fields are marked *

Produk Terkait

Request a Quote for This Machine

Send us your wire diameter, capacity and power supply requirements — we reply with price and lead time within 24 hours.

Send Your Requirements

Tell us what you need — we reply with price, lead time and shipping cost within 24 hours.

🔒 Your details are kept confidential and never shared. We reply within 24 hours.

Frequently Asked Questions

What wire diameter range can these machines handle?

The range runs from small wire around 1.2 mm up to 25 mm rebar, depending on the model. Each machine has a stated straightening diameter range and cutting length range, both of which should be confirmed in writing before ordering.

How accurate is the cutting length?

Cutting length tolerance varies by model. Smaller machines are typically rated to about plus or minus 1 mm, while larger hub and hydraulic machines are commonly rated to within 5 mm. Straightening accuracy is usually stated separately, around 1 mm per metre.

Can it cut both round and threaded rebar?

Yes. Several models in the range are built for both round steel and threaded steel, and profile machines can also handle square, hexagonal and flat steel with the appropriate tooling. Confirm the material you need when specifying.

What is the difference between the hub type and the CNC hydraulic type?

Hub type machines use a rotating hub to straighten wire and are suited to a wide diameter range at moderate speed. CNC hydraulic machines use hydraulic cut-off with programmable length control, which suits repeat production runs and higher accuracy requirements.

How fast do they run?

Straightening speed is typically up to about 30 m/min on the larger machines, with small wire machines running faster. Actual output depends on cut length as much as line speed, since short cuts mean more cutting cycles per metre.

Can the machine be configured for our production line?

Yes. Cutting length range, motor power, voltage and control configuration can all be specified. Most machines in this range are built to order rather than supplied from stock.

Scroll to Top