GTS16-25 Hub Type Straightening and Cutting Machine

Mesin Pelurus dan Pemotong Kawat Tipe Poros GTS16-25

Mulai $1,000

Mesin pelurus dan pemotong tipe hub presisi tinggi untuk besi beton Φ16–25 mm, dengan kontrol penggerak frekuensi variabel ganda.

Kategori:

From $1,000

⚙
Dapat disesuaikanSemua parameter dapat disesuaikan dengan kebutuhan produksi Anda. Harga akhir dikutip sesuai spesifikasi yang Anda konfirmasi.

Ikhtisar

Mesin pelurus dan pemotong kawat tipe hub berat untuk baja tulangan besar, dirancang untuk presisi tinggi dan hasil tanpa goresan. Kontrol konversi frekuensi ganda menjaga kecepatan traksi dan pelurusan tetap tersinkronisasi, dan pemotongan hidraulik menghasilkan ujung yang bersih. Menangani batang Φ16–25 mm hingga 30 m/min.

Fitur Utama

  • Pelurusan presisi tinggi tanpa goresan
  • Kontrol konversi frekuensi ganda (pengubah frekuensi variabel)
  • Menangani besi beton besar: Φ16–25 mm
  • Panjang potong 5000–10000 mm
  • Motor pelurus traksi 45 kW

Spesifikasi Teknis

Diameter bahan yang diluruskan Φ16–Φ25 mm
Panjang potong otomatis 5000–10000 mm
Kesalahan panjang potong ≤ 5 mm
Akurasi pelurusan ≤ 1 mm/m
Kecepatan pelurusan ≤ 30 m/min
Daya motor penarikan dan pelurusan 45 kW
Daya motor pemotong hidraulik Y160-4 / 11 kW
Daya motor pelumasan 40–90 W

Kirimkan kepada kami rentang diameter kawat, material, dan output yang diperlukan — teknisi kami akan mengonfirmasi spesifikasi tepat dan penawaran harga dalam 24 jam.

Ulasan

Belum ada ulasan.

Jadilah yang pertama memberikan ulasan “Mesin Pelurus dan Pemotong Kawat Tipe Poros GTS16-25”

Your email address will not be published. Required fields are marked *

Produk Terkait

Request a Quote for This Machine

Send us your wire diameter, capacity and power supply requirements — we reply with price and lead time within 24 hours.

Send Your Requirements

Tell us what you need — we reply with price, lead time and shipping cost within 24 hours.

🔒 Your details are kept confidential and never shared. We reply within 24 hours.

Frequently Asked Questions

What wire diameter range can these machines handle?

The range runs from small wire around 1.2 mm up to 25 mm rebar, depending on the model. Each machine has a stated straightening diameter range and cutting length range, both of which should be confirmed in writing before ordering.

How accurate is the cutting length?

Cutting length tolerance varies by model. Smaller machines are typically rated to about plus or minus 1 mm, while larger hub and hydraulic machines are commonly rated to within 5 mm. Straightening accuracy is usually stated separately, around 1 mm per metre.

Can it cut both round and threaded rebar?

Yes. Several models in the range are built for both round steel and threaded steel, and profile machines can also handle square, hexagonal and flat steel with the appropriate tooling. Confirm the material you need when specifying.

What is the difference between the hub type and the CNC hydraulic type?

Hub type machines use a rotating hub to straighten wire and are suited to a wide diameter range at moderate speed. CNC hydraulic machines use hydraulic cut-off with programmable length control, which suits repeat production runs and higher accuracy requirements.

How fast do they run?

Straightening speed is typically up to about 30 m/min on the larger machines, with small wire machines running faster. Actual output depends on cut length as much as line speed, since short cuts mean more cutting cycles per metre.

Can the machine be configured for our production line?

Yes. Cutting length range, motor power, voltage and control configuration can all be specified. Most machines in this range are built to order rather than supplied from stock.

Scroll to Top