GTS5-12 & GTS10-20 Hub Type Straightening and Cutting Machine

Mesin Pelurus dan Pemotong Kawat Tipe Hub GTS5-12 & GTS10-20

Mulai $1,000

Mesin pelurus dan pemotong kawat tipe hub untuk baja tulangan 5–20 mm dengan kontrol VFD ganda.

Kategori:

From $1,000

⚙
Dapat disesuaikanSemua parameter dapat disesuaikan dengan kebutuhan produksi Anda. Harga akhir dikutip sesuai spesifikasi yang Anda konfirmasi.

Ringkasan

Dua model mencakup besi beton 5–12 mm dan 12–20 mm. Desain pelurusan tipe hub dengan kontrol konversi frekuensi ganda menghasilkan batang lurus presisi tinggi tanpa goresan. Pemotongan otomatis dari 100 mm hingga 10000 mm.

Fitur Utama

  • Dua model: GTS5-12 dan GTS10-20
  • Pelurusan presisi tinggi tanpa goresan
  • Kontrol konversi frekuensi ganda
  • Panjang pemotongan 100–10000 mm
  • Lengkap dengan pemotong hidraulik dan stasiun pompa oli

Spesifikasi Teknis

Model GTS5-12 GTS10-20
Diameter bahan yang diluruskan 5–12 mm 12–20 mm
Panjang potong otomatis 100–10000 mm 100–10000 mm
Kesalahan panjang potong ≤ 5 mm ≤ 5 mm
Akurasi pelurusan ≤ 1 mm/m ≤ 1 mm/m
Kecepatan pelurusan ≤ 30 m/min ≤ 30 m/min
Daya motor traksi Y132S-4 / 5.5 kW Y132-4 / 7.5 kW
Daya motor poros Y160M-4 / 11 kW 22 kW
Daya motor pemotong hidrolik 5.5 kW 7.5 kW
Dimensi bagian pelurus 3800 × 1030 × 1150 mm 3800 × 1300 × 1400 mm
Dimensi stasiun pompa oli 1150 × 900 × 900 mm 1150 × 900 × 900 mm
Berat 2300 kg 3400 kg

Kirimkan kepada kami rentang diameter kawat, material, dan output yang dibutuhkan — insinyur kami akan mengonfirmasi spesifikasi tepat dan memberikan penawaran dalam 24 jam.

Ulasan

Belum ada ulasan.

Jadilah yang pertama memberikan ulasan “Mesin Pelurus dan Pemotong Kawat Tipe Hub GTS5-12 & GTS10-20”

Your email address will not be published. Required fields are marked *

Produk Terkait

Request a Quote for This Machine

Send us your wire diameter, capacity and power supply requirements — we reply with price and lead time within 24 hours.

Send Your Requirements

Tell us what you need — we reply with price, lead time and shipping cost within 24 hours.

🔒 Your details are kept confidential and never shared. We reply within 24 hours.

Frequently Asked Questions

What wire diameter range can these machines handle?

The range runs from small wire around 1.2 mm up to 25 mm rebar, depending on the model. Each machine has a stated straightening diameter range and cutting length range, both of which should be confirmed in writing before ordering.

How accurate is the cutting length?

Cutting length tolerance varies by model. Smaller machines are typically rated to about plus or minus 1 mm, while larger hub and hydraulic machines are commonly rated to within 5 mm. Straightening accuracy is usually stated separately, around 1 mm per metre.

Can it cut both round and threaded rebar?

Yes. Several models in the range are built for both round steel and threaded steel, and profile machines can also handle square, hexagonal and flat steel with the appropriate tooling. Confirm the material you need when specifying.

What is the difference between the hub type and the CNC hydraulic type?

Hub type machines use a rotating hub to straighten wire and are suited to a wide diameter range at moderate speed. CNC hydraulic machines use hydraulic cut-off with programmable length control, which suits repeat production runs and higher accuracy requirements.

How fast do they run?

Straightening speed is typically up to about 30 m/min on the larger machines, with small wire machines running faster. Actual output depends on cut length as much as line speed, since short cuts mean more cutting cycles per metre.

Can the machine be configured for our production line?

Yes. Cutting length range, motor power, voltage and control configuration can all be specified. Most machines in this range are built to order rather than supplied from stock.

Scroll to Top